HP Printer Error Code 58: How to Fix It

Medium 30-60 minutes Medium Severity Verified June 2026
Summarize with ChatGPTSummarize with ClaudeSummarize with Perplexity Add as Preferred Source on Google
Error Code
58
Brand
HP
Product Type
printer
Severity
Medium
DIY Difficulty
Medium
Estimated Fix Time
30-60 minutes
HP Printer Error Code 58 indicates a fan motor fault inside your printer. The internal cooling or fuser fan has stopped working correctly, which causes the printer to halt to prevent overheating damage. This is a medium-severity issue that can sometimes be resolved at home by cleaning, resetting, or replacing the faulty fan component.
Ad

Tools You'll Need

How to Fix Error Code 58

  1. Power Off and Unplug the Printer

    Always unplug the printer before opening any panels or inspecting internal components. Working on a powered printer risks electric shock and damage to sensitive parts.

  2. Perform a Full Cold Reset

  3. Check and Clean the Fan Vents and Air Intake Areas

    Use compressed air in a well-ventilated area. Do not shake the can or tilt it while spraying, as this can release liquid propellant into the printer.

  4. Open the Printer and Inspect the Internal Fan

    Do not attempt to open the printer while it is plugged in. The fuser area can retain heat even after power-off — allow 10 minutes of cool-down time before handling internal components near the fuser.

  5. Inspect the Fan Wiring and Connector

    Do not attempt to splice or tape damaged wiring as a permanent fix. Damaged wiring near a heat source like the fuser is a fire hazard.

  6. Replace the Faulty Fan Assembly

    Ensure you purchase a fan assembly rated for your exact HP printer model. Installing an incompatible fan may not clear the error or could cause further damage.

  7. Update Printer Firmware

Parts You May Need

Internal cooling fan assembly
Check Price on Amazon
Fan wiring harness
Check Price on Amazon
DC controller board
Check Price on Amazon
Internal cooling fan assembly
Check Price on Amazon
Fan wiring harness
Check Price on Amazon
DC controller board
Check Price on Amazon
Internal cooling fan assembly
Check Price on Amazon
Fan wiring harness
Check Price on Amazon
DC controller board
Check Price on Amazon
Ad

When to Call a Professional

If you have completed all steps above and Error Code 58 still appears, or if you found burned wiring, a damaged DC controller board, or signs of electrical burning inside the printer, stop and contact an HP-authorized service technician. Additionally, if your printer is under warranty, do not open the casing — contact HP support directly as opening the printer may void your warranty. Professional repair is also recommended if you are not comfortable working with internal electronics.

Frequently Asked Questions

What does HP printer error code 58 mean?
Error code 58 on an HP printer means the printer has detected a fan motor fault. One of the internal cooling fans — typically the main cooling fan or the fuser fan — has stopped working properly or isn't running at the expected speed. The printer shuts down to prevent heat damage.
Can I fix HP error code 58 without opening the printer?
Sometimes, yes. Start by unplugging the printer for 60 seconds and performing a cold reset. Also clean the external ventilation vents with compressed air to remove any dust blockages. If the fan was only stalling due to a clog or a temporary sensor glitch, these steps may resolve the error without needing to open the printer.
How much does it cost to fix HP printer error code 58?
If you do it yourself, the main cost is a replacement internal cooling fan assembly, which typically costs between $10 and $40 depending on your HP printer model. If you take it to a repair technician, labor costs can range from $50 to $150 or more. For older or lower-cost printer models, it may be more economical to replace the printer.
Is error code 58 the same as error code 58.0 or 58.04 on HP printers?
Yes. HP often displays extended error codes such as 58.0, 58.03, or 58.04 which are sub-variants of the base Error 58 fan fault. The sub-codes can indicate which specific fan is failing (for example, the main cooling fan versus the fuser fan), but the troubleshooting steps are largely the same: inspect, clean, and if necessary replace the faulty fan assembly.
Why does my HP printer keep showing error 58 even after replacing the fan?
If Error 58 returns after replacing the fan, the problem may lie with the wiring harness connecting the fan to the DC controller board, or the DC controller board itself may be faulty. A failed board can incorrectly report a fan fault even when the fan is working correctly. In this case, professional diagnosis is recommended, as DC controller board replacement is an advanced repair.

Related Error Codes